DI-9M-08CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
 |
  |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
 | Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-08CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-08日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-08日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
最新產品
- Lindstrom鑷子TL 15AGWHM 2025/5/9 20:42:12
- Lindstrom鑷子TL 15AGW 2025/5/9 20:38:07
- Lindstrom鑷子TL 15A 2025/5/9 20:27:11
- Rubis剪刀1F002S/EL 2025/5/9 20:01:12
- Rubis剪刀1F002/EL 2025/5/9 19:58:31
- Rubis剪刀1F000S/EL 2025/5/9 19:55:56
- Rubis剪刀1F000/EL 2025/5/9 19:52:56
- Rubis剪刀1C300ES/EL 2025/5/9 19:47:22
- 半導體塞貝克系數電阻測試儀 2025/5/9 18:10:29
- 上海高層外墻防水修繕專家 裝飾條脫落拆除防水 2025/5/9 18:07:57
- MOOG穆格伺服閥RT7625E-1089-4 2025/5/9 18:07:10
- MOOG穆格伺服閥D633-410B 2025/5/9 18:07:08
- MOOG穆格伺服閥D634K2008C 2025/5/9 18:07:05
- MOOG穆格伺服閥D661-4656 2025/5/9 18:07:02
- MOOG穆格伺服閥G75HOAO6VSP2H.A 2025/5/9 18:07:00
- MOOG穆格伺服閥D633-390B 2025/5/9 18:06:56
- MOOG穆格伺服閥D633-342B 2025/5/9 18:06:53
- MOOG穆格伺服閥D661-1942E 2025/5/9 18:06:50
- MOOG穆格伺服閥771-121 2025/5/9 18:06:47
- MOOG穆格伺服閥D633K2024B 2025/5/9 18:06:45
- MOOG穆格伺服閥D661-4412C 2025/5/9 18:06:42
- MOOG穆格伺服閥D661-4015 2025/5/9 18:06:39
- MOOG穆格伺服閥D661-4011 2025/5/9 18:06:37
- MOOG穆格伺服閥D633-419B 2025/5/9 18:06:34
- MOOG穆格伺服閥D661-4677C 2025/5/9 18:06:32
- MOOG穆格伺服閥S25J0QA6VSX2-B 2025/5/9 18:06:29
- MOOG穆格伺服閥79-300A 2025/5/9 18:06:27
- MOOG穆格伺服閥J761-004 2025/5/9 18:06:25
- MOOG穆格伺服閥760C564 2025/5/9 18:06:22
- MOOG穆格伺服閥D661-246A 2025/5/9 18:06:20